Search
Specification • The receiver shall send a positive acknowledgment (ACK) packet for each DATA packet received without error.
Allocation of Service Types and Subtypes
Specification • The PUS provides a standard set of services that are targeted for communication between spacecraft and ground systems. Many of them may not be applicable to on-board communication between applications. However, nothing precludes their use in a JAS-based system. The PUS can be extended to add additional functionality to existing...
Backplane Connectors
Specification • JAS electrical design should utilize commercial connector standards when applicable. The VPX plug-in module to backplane connector is a Tyco Electronics MultiGig RT2 connector system which was chosen for its rugged mechanical performance and high-speed electrical performance, rated to 6.4 Gb/s and demonstrated to support data rates greater than 10...
Backplane Topology
Specification • The backplane is a key element in achieving high-speed connections between the plug-in modules or nodes in the case of a JAS system. VPX compliant backplanes support a minimum signaling rate of at least 3.125 Gbps on any differential point-to-point connection. There are a small number of required signals on...
Buckling and Crippling
Specification • Evaluation of buckling strength shall consider the combined action of primary and secondary stresses and their effects on general instability, local or panel instability, crippling, and creep.
Buffer Fragmentation and Reassembly
Specification • In cases where a higher-level transmit application (or higher layer in a communications stack) must transmit a buffer of data that exceeds the JRDDP MTU size, the buffer must be fragmented into a series of JRDDP packets and then reassembled at the receive TEP before returning the buffer to the...
Buffer Segmentation and Reassembly
Specification • In cases where a higher-level transmit application, or higher layer in a communications stack, must transmit a buffer of data that exceeds the JEEP MTU size, the buffer must be segmented into a series of JEEP packets and then reassembled at the receive TEP before returning the buffer to the...
CCSDS Telecommand and Telemetry Format Packet Standard
Specification • CCSDS Space Packet The CCSDS packet format consists of a packet primary header and packet data field. The header provides routing information for the packet and metadata that describes the packet. The data field is intended to be a user-defined field that can be customized for applications. Details of how...
Channel Closing Process
Specification • The following sections present the interactions (in the form of UML Sequence Diagrams) between transmit and receive endpoints while closing a channel. Various error conditions are presented in order to show nominal, delayed, and worst case scenarios. The hexagonal icons represent the TEP states while the dashed green lines represent...
Channel Independence
Specification • Each transport channel shall operate independently from other transport channels.
Channel Operations
Specification •
Coating Surface Resistivity
Specification • The thickness of all chemical film treatments need to be controlled to provide low surface resistivity. Surface resistivity shall be less than 1 x 109 ohm/ square.
Coating Volume Resistivity
Specification • All paints and coatings shall have a volume resistivity less than 1 x 109 ohm-cm.
Communication Data Links
Specification • JAS nodes should communicate through one or more standard communications protocols. Serial communication protocols are the recommended approach but JAS does not preclude the use of parallel communication protocols. JAS also does not preclude the use of custom or legacy based communications.
Coordinate Definition
Specification • The JAS mechanical structure shall implement a coordinate system as a reference point for the design. The mounting of each component should be considered as the coordinate reference. The coordinate frame can originate on a pin-and-slot mounting. [Placeholder: Defining a coordinate frame helps to determine center of gravity, mass, envelopes...
Data Transmit Queue
Specification • When packets from more than one channel are available for transmit, packets shall be transmitted in the order in which they are queued and in accordance with the transmit priority described above.
Delayed Case
Specification • A delayed but recoverable scenario occurs when a receive TEP receives at least one CLOSE packet but the transmit TEP does not receive any ACK packets as shown in Figure 3. In this case the receive TEP will eventually transition to the CLOSED state via the timeout and the transmit...
Design Thickness
Specification • For strength and buckling analyses, minimum material thickness shall be used. Minimum thickness is defined as the nominal thickness minus the lower tolerance and applies to metallic and nonmetallic structural elements. For modeling purposes and stiffness calculations, use nominal or expected values. For flexures the Maximum blade thickness shall be...
Design Ultimate Load
Specification • The JAS mechanical structure shall have sufficient strength to simultaneously withstand design ultimate loads, the corresponding temperature, pressure and accompanying environmental phenomena without failure.
Design Yield Load
Specification • The JAS mechanical structure shall withstand design yield loads, the corresponding temperature, pressure and associated environmental phenomena without permanent deformations, or permanent misalignments, of all components.
ECSS Packet Utilization Standard
Specification • The figures below show a PUS telecommand and telemetry packet and their utilization within the CCSDS space packet specification. The PUS specification uses the user-definable fields of the CCSDS space packet in order to create a PUS packet. The specification defines a secondary header that provides additional metadata such as...
Electrical Bonding
Specification • Each equipment design shall provide electrical continuity across mechanical interfaces in accordance with the design requirements of this specification. Electrical continuity will be achieved to the maximum practical extent by direct metal-to-metal contact across the entire interface surface. If the electrical resistance across mechanical interfaces is measured to be less...
Electrical Interconnects
Specification • JAS electrical design shall utilize commercial interconnect standards when applicable. The following sections are some examples of commercial interconnect standards that are recommended but not required.
Electromagnetic Compatibility
Specification • Electromagnetic Interference (EMI) and Electromagnetic Compatibility (EMC) are important design considerations which can be mitigated by the mechanical structure. EMI limits may be in place due to application-specific requirements, but more importantly, EMI can be detrimental to electronics because of the sensitive nature of many of the modern systems and...
Envelope
Specification • The assembled JAS mechanical structure shall attempt to fit the space available without violating any system-level keep out zones.
Results 1–25 of 113